- #Cisco vpn client ipsec license key#
- #Cisco vpn client ipsec software#
- #Cisco vpn client ipsec series#
Sa_trans= esp-des esp-sha-hmac, sa_conn_id= 5 IPSEC(spi_response): getting spi 194838793 for SA IPSEC(spi_response): getting spi 203563166 for SA Protocol= ESP, transform= esp-des esp-sha-hmac IPSEC(validate_proposal_request): proposal part #2, Invalid attribute combinations between peers will show up as "atts SA life duration (VPI) of 0x0 0x46 0x50 0x0 Checking IPSec proposal 1transform 1, ESP_DES This output shows an example of the debug crypto ipsec command. (Four messages appear if you perform ESP and AH.) Two "sa created" messages appear with one in each direction. Src_proxy and dest_proxy are the client subnets. This command shows the source and destination of IPsec tunnel endpoints. message ID = 800032287 debug crypto ipsec message ID = 0Ĭhecking ISAKMP transform against priority 1 policy This output shows an example of the debug crypto isakmp command. Since phase 2 (security associations) SAs are unidirectional, each SA shows traffic in only one direction (encryptions are outbound, decryptions are inbound). This command shows each phase 2 SA built and the amount of traffic sent. Outbound pcp sas: show crypto engine connection active Slot: 0, conn id: 3443, flow_id: 1444, crypto map: test Sa timing: remaining key lifetime (k/sec): (4608000/52) Slot: 0, conn id: 3442, flow_id: 1443, crypto map: test #pkts decompress failed: 0, #send errors 1, #recv errors 0 #pkts compressed: 0, #pkts decompressed: 0 interface: FastEthernet0Ĭrypto map tag: test, local addr. This output shows an example of the show crypto ipsec sa command. Authentication Header (AH) is not used since there are no AH SAs. You can see the two Encapsulating Security Payload (ESP) SAs built inbound and outbound. The encrypted tunnel is built between 12.1.1.1 and 12.1.1.2 for traffic that goes between networks 20.1.1.0 and 10.1.1.0. This command shows IPsec SAs built between peers. dst src state conn-id slotġ2.1.1.2 12.1.1.1 QM_IDLE 1 0 show crypto ipsec sa This command shows the Internet Security Association Management Protocol (ISAKMP) security associations (SAs) built between peers. Refer to Common IPsec Error Messages and Common IPsec Issues for more details.
#Cisco vpn client ipsec software#
The topics in this section describe the Cisco IOS Software debug commands. Refer to Cisco Technical Tips Conventions for more information on document conventions. If your network is live, make sure that you understand the potential impact of any command. All of the devices used in this document started with a cleared (default) configuration. The information in this document was created from the devices in a specific lab environment.
#Cisco vpn client ipsec license key#
PIX-V5.0 and later, which requires a single or triple DES license key in order to activate.
#Cisco vpn client ipsec series#
Triple DES is available on the Cisco 2600 series and later.
K2-Indicates triple DES feature (on Cisco IOS Software Release 12.0 and later). The information in this document is based on these software and hardware versions:ĥ6i-Indicates single Data Encryption Standard (DES) feature (on Cisco IOS Software Release 11.2 and later). There are no specific requirements for this document. It contains a checklist of common procedures that you might try before you begin to troubleshoot a connection and call Cisco Technical Support. Refer to Most Common L2L and Remote Access IPsec VPN Troubleshooting Solutions for information on the most common solutions to IPsec VPN problems. This document assumes you have configured IPsec. This document describes common debug commands used to troubleshoot IPsec issues on both the Cisco IOS ? Software and PIX/ASA.
0 kommentar(er)
